Citrix Systems Server 4.2 Manuel d'utilisateur Page 43
- Page / 194
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Upgrade from 2.2.x to 4.2
35
g. Install a libvirt hook with the following commands:
# mkdir /etc/libvirt/hooks
# cp /usr/share/cloudstack-agent/lib/libvirtqemuhook /etc/libvirt/hooks/qemu
# chmod +x /etc/libvirt/hooks/qemu
h. Restart libvirtd.
# service libvirtd restart
i. Start the agent.
# service cloudstack-agent start
19. Log in to the CloudPlatform UI as admin, and check the status of the hosts. All hosts should come
to Up state (except those that you know to be offline). You may need to wait 20 or 30 minutes,
depending on the number of hosts.
Do not proceed to the next step until the hosts show in the Up state. If the hosts do not come to
the Up state, contact support.
20. Run the following script to stop, then start, all System VMs including Secondary Storage VMs,
Console Proxy VMs, and virtual routers.
a. Run the command once on one management server. Substitute your own IP address of the
MySQL instance, the MySQL user to connect as, and the password to use for that user. In
addition to those parameters, provide the "-c" and "-r" arguments. For example:
# nohup cloudstack-sysvmadm -d 192.168.1.5 -u cloud -p password -a > sysvm.log 2>&1 &
This might take up to an hour or more to run, depending on the number of accounts in the
system.
b. After the script terminates, check the log to verify correct execution:
# tail -f sysvm.log
The content should be like the following:
Stopping and starting 1 secondary storage vm(s)...
Done stopping and starting secondary storage vm(s)
Stopping and starting 1 console proxy vm(s)...
Done stopping and starting console proxy vm(s).
Stopping and starting 4 running routing vm(s)...
Done restarting router(s).
c. If you would like additional confirmation that the new system VM templates were correctly
applied when these system VMs were rebooted, SSH into the System VM and check the
version.
Use one of the following techniques, depending on the hypervisor.
- CloudPlatform 1
- (powered by Apache 1
- CloudStack) Version 1
- 4.2 Installation Guide 1
- Installation Guide 2
- 1.2. Citrix Knowledge Center 9
- 1.3. Contacting Support 9
- Concepts 11
- 2.3.3. Networking Overview 14
- Networking Overview 15
- Cloud Infrastructure Concepts 17
- 3.3. About Pods 19
- 3.4. About Clusters 20
- 3.5. About Hosts 21
- 3.6. About Primary Storage 21
- 3.7. About Secondary Storage 22
- 3.8. About Physical Networks 22
- Upgrade Instructions 27
- # service libvirtd restart 34
- # tail -f sysvm.log 34
- XenServer or KVM: 35
- # service cloud-agent stop 42
- # ./install.sh 42
- # cloudstack-agent-upgrade 42
- # xe pool-list 45
- # xe host-list 45
- Installation 51
- Requirements 52
- 5.3.3.1. CloudPlatform 4.x 53
- 5.3.3.2. CloudPlatform 3.x 54
- 5.3.3.3. CloudPlatform 2.x 54
- # cloudstack-setup-management 60
- <list> 63
- 5.4.7. Prepare NFS Shares 64
- # umount /mnt/secondary 70
- # rmdir /mnt/secondary 70
- User Interface 77
- 6.3.3. Creating an Instance 81
- 6.3.5. Resetting SSH Keys 81
- Infrastructure 83
- 7.2.2. Adding a Region 84
- 7.2.4. Deleting a Region 86
- 7.3. Adding a Zone 87
- 7.4. Adding a Pod 96
- 7.5. Adding a Cluster 97
- 7.5.3. Add Cluster: vSphere 98
- 7.6. Adding a Host 101
- password] 102
- # ./cloud-setup-bonding.sh 102
- 7.7. Adding Primary Storage 103
- 7.8. Adding Secondary Storage 104
- 7.9. Initialize and Test 106
- Initialize and Test 107
- 8.4. Username and Password 110
- 8.5. Time Synchronization 110
- 8.6. Licensing 111
- XenServer (Optional) 114
- (Optional) 114
- # hostname --fqdn 120
- # yum erase qemu-kvm 120
- 10.1.1. Software requirements 125
- 10.1.2. Hardware requirements 125
- 10.1.4. Other requirements: 126
- 10.2.1. vCenter Checklist 127
- 10.4. ESXi Host setup 128
- 10.5.1.2. Increasing Ports 129
- Virtual Switch 130
- 10.6.3.4. Adding VLAN Ranges 133
- 10.7.2. Add iSCSI target 140
- Bare Metal Installation 143
- 11.3.1. Download the Software 144
- 11.3.2. Set Up IPMI 144
- 11.3.5. Set Up a File Server 146
- # mkdir –p /home/centos63 148
- 13.1. Small-Scale Deployment 165
- 13.5. Multi-Site Deployment 167
- Network Setup 169
- 14.2. VLAN Allocation Example 170
- 14.4. Layer-2 Switch 171
- 14.5. Hardware Firewall 172
- 14.5.3.1.2. Prerequisites 176
- ASA1000V(config)# reload 179
- 14.7. Topology Requirements 181
- http://inmon.com 183
- Amazon Web Service Interface 185
- 15.5. Supported AWS API Calls 187
- 16.2. SSL (Optional) 191
- 16.3.1. Failover 194
Produits connexes et manuels pour Logiciel Citrix Systems Server 4.2
(68 pages)LG DH3130S podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Odtwarzacze DVD LG DH3130S.
Dostarczamy 6 pdf podręczników LG DH3130S do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commentaires sur ces manuels